Cast Iron Collector Forums  
Google

Go Back   Cast Iron Collector Forums > General Discussion > Cast Iron Cleaning and Seasoning

Notices

Cast Iron Cleaning and Seasoning Help With and Tips & Techniques For Cast Iron Cookware Restoration

Reply
 
Thread Tools Display Modes
  #1  
Old 01-24-2018, 09:26 PM
Brennan O'Connor Brennan O'Connor is offline
New Member
 
Join Date: Jan 2018
Posts: 2
Default Re-polishing the Cooking Surface of a Griswold #8?

Ok, hear me out,
I am pretty new to this. I recently picked up a skillet with some rust pitting in a corner between the bottom cooking surface and the inside of the wall. I think the skillet may have sat at an angle with a bit of water in it for some considerable time. I want the interior of this skillet to be smooth, and obviously the only way to achieve that would be to remove some of the original surface to even it up with the pitted corner. I understand that this is generally discouraged, especially on older pieces. That said, there is already very noticeable damage to the original surface, in the form of pitting.

I saw this video, and I though I might try it out, seeing as how it doesn't involve power tools and may result in a finish not too different that what would have been produced at the factory when the skillet was new.

What do you all think about this? Is this a reasonable way to address pitting on an otherwise very nice Slant EPU?
Reply With Quote
Sponsored Links
  #2  
Old 01-24-2018, 09:43 PM
Doug D. Doug D. is offline
Site Admin
 
Join Date: Mar 2012
Posts: 5,686
Default Re: Re-polishing the Cooking Surface of a Griswold #8?

Hard to say without a photo, but I have a user pan that sounds like that. I just cooked in it until the pitting filled in with seasoning. The pitting has already removed some iron, doesn't seem to be much point in removing more.
Reply With Quote
  #3  
Old 01-24-2018, 09:59 PM
SeanD SeanD is offline
Senior Member
 
Join Date: Jul 2016
Location: Clearfield, PA
Posts: 361
Default Re: Re-polishing the Cooking Surface of a Griswold #8?

I agree with not doing it. I have a pan that's pitted pretty bad, but after about 2 years of fairly regular use, the pits are less then half as deep already, and they were deep pits, not little ones. Just give it time, cook in it, and maintain the seasoning, you'll be fine.
Reply With Quote
  #4  
Old 01-25-2018, 09:44 AM
Ty L. Ty L. is offline
Senior Member
 
Join Date: Aug 2015
Location: Milwaukee, WI
Posts: 433
Default Re: Re-polishing the Cooking Surface of a Griswold #8?

I tried grinding the pitting out of a #7 skillet. Took hours, couldn't get the inner sidewalls without gouging the heck out of it so they're still pitted, couldn't completely get the swirl marks from the grinder off the cooking surface either. At first, and likely because it was as smooth and shiny as stainless steel (despite me using nothing finer than 60 grit!), I couldn't get seasoning to hold. Eventually I dunked the pan into a stock pot full of boiling water for 15 minutes or so, pulled it out long enough for it's own heat to evaporate the water on it, admired the bluish tint the iron was beginning to take, ignored the flash rust, and then dunked again. I did that a few times, always ignoring the flash rust and then immediately went on to seasoning it. The seasoning held, but what a waste of time!

I have a pair of 3-notch Lodge #10's. Bought them last summer, about a month apart. One has pitting on about a third of the cooking surface, all in the same general area. The other doesn't. Both had rust and were restored the same way: the e-tank, scrubbing with soapy water, and 2 rounds of manual seasoning. They're both my go-to #10 pans so they're getting used reguarly. Most of the time when I grab for one I don't care which. They're both equally nonstick and being the same brand and style cook exactly the same. The only exception: I'll always take the pitted one when camping or cooking over a wood fire simply because the cosmetic flaw gives it a lower dollar value.
Reply With Quote
  #5  
Old 01-25-2018, 11:07 AM
Brennan O'Connor Brennan O'Connor is offline
New Member
 
Join Date: Jan 2018
Posts: 2
Default Re: Re-polishing the Cooking Surface of a Griswold #8?

Ok,
Thanks for the perspective everyone. I have decided just to use it and not worry about the pitting.

Mostly I was just disappointed that my new (to me) #8 didn't end up looking the way I had imagined it. That's ok, though. It wont be long until the next one comes along.
Reply With Quote
Reply

Bookmarks

Tags
pitting, polishing, rust damage, sanding, surface

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Advertisement

This site is a participant in the Amazon Services LLC Associates Program,
an affiliate advertising program designed to provide a means for sites to earn
advertising fees by advertising and linking to Amazon.com or its affiliates.

All times are GMT -5. The time now is 03:05 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.